Adblock ultimate for chrome 2.161/6/2024 ![]() ![]() That USB-C port can also be used to connect an external mic. However, the base sensitivity setting rises to ISO 640.Īlthough the X-T30 has a USB-C connection that allows battery charging, there’s a battery charger supplied in the box. It’s worth noting here that the F-Log mode can be used when recording video to a memory card. Fujifilm’s other 15 Film Simulation modes are also available if you want to give stills or videos a particular look in-camera. ![]() These are designed to produce flat footage with greater scope for grading. However, when an SD card is used for storage, the output drops to 4:2:0 8bit.įurther good news is that there’s both F-Log recording and the Eterna Film Simulation mode. If an external recorder is connected via the X-T30’s HDMI port it’s possible to record 4:2:2 10bit footage. Switch to Full-HD resolution, however, and you can shoot at up to 120fps. At this resolution the maximum frame rate is 30p. In 4K mode (17:9 and 16:9), video is captured at 6K and then downsampled to 4K (4096 x 2160 or 3840 x 2160 respectively). The X-T3 made a significant step up in video features over the X-T2 and the X-T30 does the same in comparison with the X-T20. Switching to the mechanical shutter gives a maximum shooting rate of 8fps for up to 90 Jpegs or 18 raw files. Alternatively, you can shoot full-resolution images at 20fps for up to 53 Jpegs or 17 raw files. This rate can be maintained for up to 26 Jpegs or 17 raw files with no visible blackout in the viewfinder. As a result, the image resolution drops to 16Mp. This uses the electronic shutter and there’s a 1.25x crop applied to the image. Continuous Shootingįor when you need to capture fast action, the X-T30 has a maximum continuous shooting rate of 30fps (frames per second). There are 5 preset options that let you tailor the camera’s AF response. This doesn’t offer quite as much control as the X-T3, but it’s a nice feature to have. The X-T30 can detect faces that take-up just 7% of the space.Īs before, there’s a menu section dedicated to customising the continuous Autofocus (AF-C) settings. Previously a face needed to occupy at least 10% of the vertical space. In addition, smaller or more distant faces can be detected. The X-T30’s exposure is less likely to fluctuate when a face is detected. It’s now faster and more stable than the X-T20’s. This gives 100% coverage with AF points.Įach AF point also benefits from 4x as much data.Īccording to Fuji, this, the new processing engine, an improved algorithm and the BSI design of the sensor combine to make the AF system sensitive down to -3EV.įujifilm has also worked on the Face & Eye Tracking system. For instance, there are 2.16 million pixels used for phase detection autofocusing rather than 0.5 million. This can be expended to ISO 80-51,200.Īside from the step-up in resolution from 24.3Mp to 26.1Mp, the new sensor in the X-T30 also enables a better AF system than the X-T20’s. There are even a few enhancements that have yet to reach the X-T3 via a firmware upgrade.Īs with the Fuji X-T3, the 4th generation sensor and processor combo enable a native sensitivity range of ISO 160 to 12,800. This helps boost speed, performance and image quality. In addition to the benefits of a BSI sensor, the processor is 3x faster than the previous generation. In the X-T30, Fujifilm has paired its 26.1Mp backside-illuminated (BSI) APS-C format 4th generation X-Trans CMOS sensor with the same 4th generation X-Processor as is in the X-T3.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |